15mW Regulation CO2 Laser Power Supply For B E ES ESV 110V 220V
Co2 Laser Power Supply Product Overview This 15mW CO₂ Laser Power Supply is a precision-engineered, high-stability driver specifically designed to operate B, E, ES, and ESV series low-power sealed CO₂ laser tubes. With an optical output of 15mW at 10.6μm wavelength, this power supply is ideal for ...
15mW co2 laser power supply
,110V co2 laser power supply
,220V laser tube power supply
Co2 Laser Power Supply
Product Overview
This 15mW CO₂ Laser Power Supply is a precision-engineered, high-stability driver specifically designed to operate B, E, ES, and ESV series low-power sealed CO₂ laser tubes. With an optical output of 15mW at 10.6μm wavelength, this power supply is ideal for laboratory research, optical alignment, educational demonstrations, and proof-of-concept OEM integrations.
The unit features a compact, lightweight design with forced air cooling, short-circuit and over-voltage protection, and supports both Continuous Wave (CW) and pulsed modulation modes. Its specialized output characteristics ensure optimal excitation and stable discharge for B/E/ES/ESV series tubes, delivering reliable performance in benchtop and embedded applications.
Key Features
-
B/E/ES/ESV Series Compatibility: Optimized output parameters for stable ignition and sustained discharge across all four tube series.
-
Precise 15mW Regulation: Maintains stable optical output power for consistent beam performance.
-
Dual Operation Modes: Supports both CW (Continuous Wave) and pulsed operation (0–5kHz TTL modulation).
-
Comprehensive Protections: Built-in over-voltage, over-current, open-circuit, and short-circuit protection with automatic shutdown.
-
Compact & Lightweight: Small footprint design for easy integration into laboratory setups and OEM systems.
-
User-Friendly Control: Simple TTL interface for laser on/off control and external modulation input.
Technical Specifications
| Parameter | Value | Condition / Note |
|---|---|---|
| Input | ||
| Supply Voltage | 110 / 220 VAC ±10% | 50/60Hz (selectable) |
| Max Input Power | < 50W | |
| Max Input Current | 0.5A (at 110VAC) | |
| Output (to Laser Tube) | ||
| Output Voltage Range | 10 – 15 kVDC | Typical for B/E/ES/ESV 15mW tubes |
| Output Current Range | 3 – 8 mA | Adjustable |
| Max Output Power (Electrical) | ~100W | |
| Efficiency | ≥ 85% | At full load |
| Control & Interface | ||
| Modulation Frequency | 0 – 5 kHz | TTL / PWM input |
| Response Time (Rise/Fall) | < 100 µs | |
| Control Interface | DB-9 / Terminal Block | Laser on/off, current adjust, interlock |
| Protection & Environment | ||
| Protections | Over-voltage, Over-current, Open-circuit, Short-circuit | Auto-recovery after fault cleared |
| Cooling Method | Forced Air Cooling | Built-in fan |
| Operating Temperature | 0°C to +40°C | |
| Storage Temperature | -20°C to +70°C | |
| Relative Humidity | ≤ 90% (non-condensing) | |
| Physical | ||
| Dimensions (L×W×H) | 150 × 100 × 50 mm | Approximate, excluding connectors |
| Weight | 0.8 kg | |
| High Voltage Cable Length | 1.0 meter | Included, with dedicated connector for B/E/ES/ESV |
Compatibility Matrix
| Laser Tube Series | Compatibility | Recommended Output Current | Notes |
|---|---|---|---|
| B Series | Fully Compatible | 3 – 5 mA | Standard low-power tubes |
| E Series | Fully Compatible | 4 – 6 mA | Enhanced efficiency design |
| ES Series | Fully Compatible | 5 – 7 mA | Extended stability version |
| ESV Series | Fully Compatible | 6 – 8 mA | High-voltage variant |
Applications
-
Scientific research and laboratory experiments
-
Optical system alignment and calibration
-
Educational laser demonstrations
-
Thin film marking and engraving (prototyping)
-
OEM integration for B/E/ES/ESV tube-based systems
Operating Instructions
-
CW Mode: Connect the "Laser On/Off" control pin to TTL high (5V) for continuous operation.
-
Pulsed Mode: Apply a TTL square wave signal (0–5V, 0–5kHz) to the modulation input pin. Laser output will follow the input signal.
-
Current Adjustment: Use the onboard potentiometer or external control voltage (0–5V) to fine-tune the discharge current within the specified range.
-
